A BLDC motor drone stator core is the stationary laminated magnetic structure of a brushless motor used in drones and unmanned aerial vehicles. It consists of stacked silicon steel laminations with precision-cut slots for copper windings. When energized by an ESC, the stator generates a rotating magnetic field that drives the rotor—directly determining the motor's torque, efficiency, and thermal behavior.

Reenives manufactures high-quality BLDC motor drone stator cores using non-grain oriented electrical steel (0.15-0.35mm) with advanced C5/C6 epoxy coating — reducing eddy current losses by up to 35% and ensuring high thermal stability for sustained drone operation.

Reenives offers BLDC motor drone stator cores in multiple configurations to meet diverse UAV application requirements:

• By Slot/Pole Config: 9N12P (high RPM racing), 12N14P (balanced torque/speed for UAVs, DLRK), 18N20P (high torque density), 24N28P (heavy-lift / eVTOL).
• By Material Thickness: 0.15mm (ultra-high performance FPV, 6S), 0.20mm (standard high-frequency UAV), 0.27mm (aerial photography), and 0.35mm (heavy-lift industrial).
• By Core Architecture: Segmented stator cores (modular for easy winding, ideal for 5-7 inch FPV racing) and integrated circular laminated stacks (one-piece for heavy-lift agricultural drones).
• By Insulation Coating: C5 epoxy powder coating (Class H, 180°C) with >2000V dielectric strength; C6 grade for superior thermal conductivity and corrosion resistance (salt spray >96h).
• By Stacking Method: Interlocking self-bonding (≥0.27mm), laser welding, or epoxy bonding (ultra-thin laminations below 0.25mm).

💡 Reenives specialty: private mould development for custom BLDC drone stator geometries — optimized for specific UAV platforms from FPV racing to heavy-lift logistics.

All parameters validated by Reenives R&D center (ISO 9001:2025 certified) and third-party testing per IEC 60404-2. Independent testing on drone motors with Reenives stator cores shows 12% higher torque density and 9°C lower winding temperature after 10-min hover compared to industry standard cores.

📐 Data source: Reenives in-house quality lab, 2025–2026. SGS verification report available. Full batch traceability and material certificates.

Reenives BLDC motor drone stator cores power critical UAV applications across multiple sectors:

• FPV Racing & Cinematic Drones: 2207, 2306, 2507 stators with 0.15-0.20mm laminations for 45,000+ RPM and 92%+ peak efficiency.
• Agricultural Spraying Drones: High-torque stators with wide slots for thicker copper windings, 0.27mm laminations for enhanced cooling, and C5/C6 epoxy coating for 500h+ salt spray resistance.
• Delivery & Logistics Drones: 12N14P / 18N20P stators for 15-50kg payload with >92% efficiency at cruise and extended range.
• eVTOL & Urban Air Mobility: Aviation-grade punching with fault-tolerant stator design and redundancy for mission-critical operations.
• Surveying & Mapping UAVs: Low-vibration stators with 0.20mm laminations for 45+ minute endurance flights.

1. Define power, RPM, and thrust requirements: For FPV racing (>40,000 RPM), select 0.15-0.20mm laminations. For heavy-lift UAVs (15,000-25,000 RPM), 0.20-0.27mm is optimal.
2. Choose lamination material thickness: 0.15mm for premium ultra-high-speed FPV performance; 0.20mm for standard UAV; 0.35mm for robust industrial drone applications.
3. Select slot/pole combination: 9N12P for high RPM racing, 12N14P for balanced torque/speed (most common for UAVs), 18N20P for high torque density heavy-lift.
4. Specify insulation and environmental protection: C5/C6 epoxy coating for outdoor UAVs; anti-corrosion treatment for maritime/agricultural drones.
5. Request samples and validation: Reenives delivers first-article inspection reports (FAI) and material certificates. Prototype BLDC drone stator samples ready in 7-10 days after design approval.

💡 Engineering support: Free DFM within 48h and FEA simulation — send your drone motor spec or drawing to linda_reenives@163.com.